Minipro Tl866cs Software Free Download [TOP]
Minipro Tl866cs Software Free Download === https://bltlly.com/2tyipD
How to Update Your Minipro TL866CS Programmer to the Latest Version
Minipro TL866CS is a high-performance universal programmer that supports over 17000 devices. It has a built-in MCU with high-speed USB interface and a VPP of 18V. However, the TL866CS programmer has ceased production and may be replaced by the newer models such as TL866II Plus or T48.
If you still have a TL866CS programmer and want to update it to the latest software version, you can follow these steps:
Download the TL866 V6.5 software from this link: http://www.autoelectric.cn/MiniPro/minipro_setup.rar
Unzip the file and run the setup.exe file to install the software on your computer.
Connect your TL866CS programmer to your computer via USB cable and launch the software.
Select \"Help\" from the menu bar and click on \"Update Firmware\".
The software will detect your programmer model and firmware version. If there is a newer version available, it will prompt you to update.
Click on \"Yes\" to start the update process. Do not disconnect or power off your programmer during the update.
Wait for the update to finish and restart your programmer.
Congratulations! You have successfully updated your Minipro TL866CS programmer to the latest version. You can now enjoy the new features and improved performance of your programmer.
If you want to upgrade your TL866CS programmer to a newer model, you may consider the TL866II Plus programmer. The TL866II Plus programmer has many advantages over the TL866CS programmer, such as:
It supports more than 31000 devices, including SPI NAND Flash, EMMC and 1.8V devices.
It has a higher programming speed and a higher VPP of 25V.
It supports simultaneous programming of up to four programmers on each computer.
It has a unique ultra-low power consumption design that does not overheat with constant use.
It has a programmable programming power supply that can automatically adjust the VCC and VPP voltages.
It has a 40-pin universal pin that can support most of the DIP devices without adapters.
It has a built-in self-test function that can check the health of the programmer and the connected devices.
It has a serial ICSP interface that can support serial and parallel high-voltage programming.
It can test the functionality of CMOS4000 series ICs and locate the gate circuit errors.
To buy a TL866II Plus programmer, you can visit the official website of XGecu, the manufacturer of TL866II Plus programmer. You can also find authorized distributors and dealers on their website. You can also check online platforms such as Amazon or eBay for TL866II Plus programmer. However, be careful of counterfeit products and make sure you buy from a reliable seller.
If you want to use the serial ICSP interface of TL866II Plus programmer, you need to connect the ICSP header on the programmer to the ICSP pins on your target device. The ICSP header has six pins: VPP, VCC, GND, CLK, DAT and PGM. The ICSP pins on your target device may vary depending on the device type and model. You can refer to the datasheet of your device or the MiniPro software for the correct pinout.
To enable the ICSP mode on TL866II Plus programmer, you need to select the \"Use ICSP interface to program\" option in the MiniPro software. You also need to select the correct device type and model from the list. Then you can perform various operations such as read, write, erase or verify on your target device.
Some tips for using the serial ICSP interface of TL866II Plus programmer are:
Make sure the power supply of your target device is stable and within the range of 1.8V to 6.5V.
Make sure the connection between the programmer and the target device is reliable and secure.
Make sure there is no interference or noise on the ICSP lines.
Make sure there is no conflict or protection on the target device that may prevent programming.
Make sure you select the correct device type and model in the MiniPro software.
Using the serial ICSP interface of TL866II Plus programmer can be very convenient and efficient for in-circuit programming. However, it may also involve some risks and challenges. Therefore, it is recommended to use a genuine and supported programmer from XGecu and follow the instructions carefully. 061ffe29dd